POPCAT to USDT ERC20: Swap Popcat for Tether on Ethereum

POPCAT is an SPL token on Solana, built around the open-mouthed cat meme. Its value swings with sentiment. USDT ERC20 is Tether on Ethereum, which aims to track the US dollar. This pair turns one into the other across two chains in a single step, with no bridge in between.

The Ethereum version suits a specific plan. Perhaps the dollars are headed for an Ethereum app, a hardware wallet already set up for Ethereum, or a recipient who only takes ERC-20 USDT. If none of that applies, other networks may fit better, and the comparison below shows the options.

Whatever the reason, the POPCAT leaves your Solana wallet and the USDT arrives at your own Ethereum address. Nothing is held in an account in between, and no ID is asked for.

The deposit is POPCAT on Solana, sent from Phantom, Solflare or a Ledger. Like any SPL token, it needs SOL to pay the transfer fee. Keep a little SOL in the wallet, because a balance of POPCAT alone cannot leave it.

Several tokens on Solana borrow the Popcat name. Before you send, open the token in Solscan from your wallet and make sure it is the POPCAT the exchange box lists, not a copy with a similar ticker.

Enter that same Solana address as the sender address in the box. It doubles as the refund address, so it should be your own wallet rather than an exchange account. Solana confirms the deposit in under a minute, which keeps the first half of this swap short. The Phantom swap guide covers the sending steps in more detail.

All four are Tether, yet they live on different chains and cannot be swapped for each other by sending. Pick the one your next destination accepts. Staying on Solana keeps a single wallet and a single fee coin; the Ethereum version usually costs more in gas each time you move it. TRC20 and BEP20 sit in between for most transfers. Whichever you choose, the receiving wallet must be on that same network, and a mismatch is the costliest error on this page. The stablecoin network comparison goes deeper.

The payout goes to an Ethereum address: 0x followed by 40 hexadecimal characters, from MetaMask, Rabby or a Ledger. Phantom can also show an Ethereum address, but its Solana address is the one you see by default, and that cannot receive ERC-20 USDT. Check that what you paste starts with 0x.

Receiving the USDT costs nothing. Moving it afterwards does, because each ERC-20 transfer pays gas in ETH. If the receiving wallet has no ETH, the USDT will sit there safely until you add some. Plan for that before you need the funds in a hurry.

Tether, the issuer, can freeze USDT at an address; that is a property of the token on every network. Ethereum confirms the payout in about 2 to 5 minutes, and Etherscan shows it under the token transfers of your address.

Most searches for this pair are price checks. The POPCAT/USDT figure you see on chart sites is a market price before any fees, and it moves constantly with a meme token's volatility.

For a swap, what matters is the amount after fees. The exchange box shows exactly how much USDT ERC20 you receive for the POPCAT you enter, using aggregated liquidity from leading crypto markets. The rate floats with the market until your Solana deposit confirms, so a fast-moving market can shift the final figure a little.

After the deposit confirms, most swaps finish within minutes, and the USDT then confirms on Ethereum. The POPCAT minimum and maximum for this pair are listed in the box as well. The guide to floating-rate pricing explains why the quote can differ slightly from what lands.

If a swap cannot be completed, the coins are refunded to the sender address you entered. For this pair that is a Solana address, and the refund arrives as POPCAT. That is why the sender address must be your own Phantom, Solflare or Ledger wallet and not a shared exchange deposit address.

Your POPCAT swap gets its own status page, opened by the swap ID. The deposit can be checked on Solscan and the payout on Etherscan. If Solscan shows the POPCAT confirmed and the status page has been still for a long time, email support@ghostswap.io with the swap ID and the Solana transaction signature. Avoid sending the POPCAT again.

To go back into Popcat later, use USDT ERC20 to POPCAT.